Home>Cable Accessories>Compounds & Resins>Compounds
Snake Tray 201 Series – Accessories include Connector Bolts, Intersections (Double Snake Tray Intersection, Universal Intersections and more), Y Connections, Connection Adapters, Cable Drop-Out Waterfalls, Beam Clamps, Wall/ Cabinet/ Rack Mount Brackets, Seismic Bracing Kits, Rods, Concrete Anchors, Cable Tray Connection Adapters and other solutions suitable for 201 series cable tray.
Snake Tray 201 Cable Tray & Accessories are utilised both below raised floors and overhead either mounted to walls or suspended from the ceiling. Snake-Eyes (mounting rings) are located along the centre spine, allowing easy attachment of threaded rod for suspended applications. The 201 Series comes in a single or double pocket design to accommodate any kind of cable run.
Snake Tray is the world’s only hand-bendable cable tray that requires no labor-intensive cutting and clipping in order to construct fast cable tray bends. Installs overhead, on walls and under access floors.
Its hand bendable design combined with Snake Tray’s built-in mounting hardware gives Snake Tray the installation cost saving advantage over any other cable tray system in today’s market. Installers are able to create turns in 10 seconds versus 20 minutes with wire mesh cable tray!
Snake Tray 201 Series – Accessories Features
Patented hand bendable design (No Fabrication required)
Built-in mounting/hanging hardware
Single connection provides both mechanical and electrical bond
Hangs from a single point
Trays nest together for compact and cost effective material handling and shipping
Open architecture allows for easy loading of cables
The CB-10 provides both a mechanical and electrical connection when joining the tray sections to one another. Only one CB-10 required per connection.
Provides a mechanical and a bonded electrical connection when joining tray sections to one another. Only one CB-12 required per connection.
Installed as either a “T” or 4-way crossing intersection component for the Double Snake 201 series tray.
Part No: CM 425D, Size: 12″ x 12″
Installed as either a “T” or 4-way crossing intersection component for a Double Snake and a Single Snake crossing.
Used to create a Y intersection or split Double Snake into two (2) separate cable paths at a terminal end.
Cable Tray Connection Adapters used to adapt 201 series to 501 series trays. Cable Tray Connection Adapters are suitable for series 201 to 501.
Installed as “T” component for the Snake 201 and 501 series trays.
Installed as 4-way crossing intersection component for the 201 Snake Tray Series.
Provides a smooth transition for cables when exiting the tray. Maintains a consistent 4″ radius eliminating kinked cables. Easily attaches to tray with cable ties.
Part No: TO-2, Size: 2″
Part No: TO-3, Size: 3″
iPart No: TO-425, Size: 4½”
Part No: TO-5, Size: 5″
Used to attach single pocket 201 series Snake Tray to the floor pedestals utilized in the construction of raised access floors.
Used to attach double pocket 201 series Double Snake to the floor pedestals utilized in the construction of raised access floors.
Wall Mount Bracket used to attach single pocket 201 series Snake Tray to walls and other vertical surfaces. Clamp to attach to tray included.
Wall Mount Bracket used to attach single pocket 201 series Snake Tray to walls and other vertical surfaces. Clamp to attach to tray included.
Used to attach single pocket 201 series Snake Tray to the tops of equipment cabinets. Clamp to attach to tray included.
Cable Tray Bracket used to mount double pocket 201 series Double Snake to the tops of equipment cabinets. Clamp to attach to tray included.
Cable Tray Bracket used to mount single pocket 201 series Snake Tray to the tops of standard equipment racks via a built-in clamping feature. No additional hardware required for this cable tray bracket. RBN-201-90 mounts to the tray perpendicularly. Clamp to attach to tray included.
Cable Tray Bracket used to mount double pocket 201 series Double Snake to the tops of standard racks via a built-in clamping feature. No additional hardware required.
Part Nos:
CM201/801-SBK1-XX: Kit for Anchoring Snake Tray and Mega Snake in Concrete Ceilings
CM 201/801-SBK-J-XX: Kit for Anchoring Snake Tray and Mega Snake around Joists
iCM 201/801-SBK-L-XX: Kit for Anchoring Snake Tray and Mega Snake with Lag Bolts into Wood Beams
CM 201/801-SB-CT: Crimp Tool
Pre-cut and pre-chased threaded rod for overhead tray installations. All rods are 3/8″-16 10/24 high strength steel as per ASTM A36 and available in 1′, 2′, 3′, 4′ 6′, and 8′ lengths. Rods are inserted through the patented Snake Eyes and secured with two 3/8″ hex nuts and one flat washer. No additional mounting accessories are necessary.
Part No: TR-1, Size: 3/8″ x 12″ Threaded Rod
Part No: TR-2, Size: 3/8″ x 24″ Threaded Rod
iPart No: TR-3, Size: 3/8″ x 36″ Threaded Rod
Part No: TR-4, Size: 3/8″ x 48″ Threaded Rod
Part No: TR-6, Size: 3/8″ x 72″ Threaded Rod
Cable Tray Concrete Wedge Anchors’ diameter equals hole diameter. Comes complete with nuts and washers ready for use. Collar expander offers 360° contact with masonry. Projections on collar immediately grip concrete.
Stud type cable tray anchor design allows easy through-type fastenings and can be set in bottomless hole. A pre-assembled cable tray anchor ensures easy and fast installation. Anchor size is same as drill bit size for easy installation. Comprehensive testing to ensure high performance in block, masonry and concrete base materials. Bulged middle section with round and diamond shaped openings prevents the anchors from spinning in the hole or dropping out when setting it overhead. Cable Tray Anchors 101 and 407 series of any applications with a 1/4″ hole.
Hanger bracket for powder-actuated fastening. Design allows for easy installation using any 8 mm power actuated fastening system. Available for both steel and concrete. The New, Versatile Hanger that Simplifies Threaded Rod Suspension.
Part No: CM FW-38, Size: Zinc Plated 3/8″ Washer
iPart No: CM HN-38, Size: Zinc Plated 3/8″ Hex Nut
This innovative fastener eliminates the labor intensive need to hand thread hex nuts up a threaded rod. Simply insert the Snake Nut anywhere on the threaded rod and tighten into place with a set screw. Once locked into place, Snake Nut has been tested to hold up to 6,800 pounds.
Part Nos: STSN 38, Size: Fits 3/8″-16 Threaded Rod
iPart Nos: STSN 12, Size: Fits ½”-13 Threaded Rod
FREE Technical Advisory Service
E-Tech Components UK Ltd maintains a free technical advisory service.
Contact us for enquiries concerning this and all other products: +44 (0) 1744 762 929
| Drawing | Part NumberCM 201-5D-8 |
|---|
